Adding a Graphics Package
Give your worn-out hull a new do with a fresh graphics package.
by Steve Noury
January 1, 2005
There are a number of things you can do to spruce up an older boat other than just applying a good
old-fashioned compound and/or wax job to the hull. But before you commit to trading in or
contracting for a new paint job, consider a graphics makeover. New graphics can modernize your
boat, and perhaps add more color or even totally transform its appearance. Here's how.
Step 1 - Before starting this application, it's important to make sure you have
the necessary tools and equipment. Some of this may be included with your package: a squeegee,
sharp knife, masking tape, color marker, clean rags, methyl hydrate (or other cleaner), dish
detergent and a couple of spray bottles. A graphics package from Raceline Digital (www.racelinedigital.com) is used
in the example. Prepare a lubricant by filling the spray bottles (1 quart) with warm water and
adding a half-teaspoon of dish detergent. This lubricant will be used to apply and align the
graphics on the side of the hull. Once you've gathered all of the tools/supplies, thoroughly clean
the hull using the odor-free methyl hydrate to remove dirt, salt and any other residue. Also,
remove any older adhesive graphics that may currently be attached to the hull.
Step 2 - The next step is to 'dry install' the graphics. This package comes with a
multicolor scheme with several layers, so be sure all of the layers line up. Start with either side
of the boat, and (in this case) hang the piece labeled A on the hull, which is usually the longest
piece, followed by B, and then C. Line up the registration squares on each piece, and temporarily
tape the ends to the hull. Check the height position using the waterline as a reference point. Look
for imperfections in the gelcoat, and reposition to cover. Avoid running graphics over any sharp
hull contours (i.e. chimes, strakes, etc.). Once satisfied with the placement, remove all but the
largest piece, (A). Mark a line on the pre-mask, extending onto the tape at both ends, using a
washable marker. Cut the tape on the pre-mask in from the edge to prevent scratching the hull with
the knife.
Step 3 - The graphics installation is done using the wet 'hinging' method. The
hull and sticky side (underside) of the graphic are sprayed with the soap/water solution. This
prevents the graphics from sticking on contact and allows for alignment. This first layer is long,
so fold into two or three sections, and apply one section at a time. Have two people lay the
graphics ' one to hold the working end of the pre-mask and one to peel back the backing, spray the
solution, and cut the excess. Shift the graphics over the wet surface to match the marks on the
tape. Squeegee to smooth the graphic and remove air bubbles. Once the pre-mask begins to haze
(about 15 minutes), remove it by slowly pulling at a 45-degree angle. Once layer A is done, wipe
down the hull with a towel. Wait a few minutes for the pre-mask to dry before attaching the next
layer.
Step 4 - Layer B is also dry-fit first, matching the squares on both layers and
taping the ends. Draw a line through the tape, and cut it on the pre-mask. This section isn't as
long as the first, so only fold in half, the backing removed to the hinge point, and any excess cut
off. Keep the hull and the underside of the graphic wet with the water/soap solution. Once in place
(squares and tape marks line up), squeegee the air bubbles, and remove the pre-mask once it begins
to haze. The last layer is short enough to apply in one piece, without folds. Repeat the same steps
as done for the first two layers. The other side of the boat is done in the same manner, although
it's not necessary to dry fit the layers. Take measurements from the completed side using
stanchions, thru-hulls, vents, etc. Once finished, wait 48 hours before launching to ensure the
adhesive fully bonds to the hull.